Hey,
could anyone post screenshots of how it looks after install?
Im not sure if Ive installed it the right way :/
Printable View
Hey,
could anyone post screenshots of how it looks after install?
Im not sure if Ive installed it the right way :/
If you see the "SBI MOD" label in the status bar, you're good to go.
Can you add the ability to apply settings to multiple torrent from extreme mod settings tab?
like in swarm tab where you can see the swarm for any number of torrents selected.
so, i select multiple torrents and then in the extreme mode tab i can set the settings to all these tabs
Hello,
first of all, im not new here, just needed to create new acc, since ive forgot old ones email.
Im using your mods for several years, and i must say thank you for everything, and good work!!!
SO far i was using vuze extreme mod, and it was working awesome (except on one tracker which doubled my download report - still dunno why).
Now id like to switch to BiglyBT, sadly i have a problem. After following step-by-step instructions, i ended up with bigly unable to run with this error: Attachment 18638. Ive also tried troubleshoot steps, tried also different locations, but no luck. Bigly, however works only without jre folder removal step. I have also checked for other java versions, deleted registry keys etc... Attachment 18639
Help please!!! Thanks
Hi, I'm using a Mac. Can I request qbittorrent 4.0.4 without global peer ID as a client file? Thanks
Hi Spidtest,
Thank you for using the correct section.You can dowload the qbittorrent 4.0.4 [NGPID] here:-Removed the client file as it contain invalid information.
Information regarding this particular client file.
1) PeerID is set to non-global. (As requested by you)
2) Key is set to Global. (As seen in Windows/Linux versions, please confirm that the Mac Version reports the same by capturing announces).
3) IPv6 and IPv4 address report disabled.(If you want either of them enabled, you have to provide me announces with IP address in it. So I can make it accordingly).
4) No forms of Encryption(s) (supported or forced). If you want it simply enable it from your settings.
Unfortunately, some torrent client (take uTorrent as an example) use different information (peer id prefix, key, reserved bytes etc) on different Operating Systems.Therefore, it would be best if you check whether or not the BiglyBT's announces (with qBittorrent client) are similar to your torrent client (qBittorrent). This can be done by capturing announces and comparing them. If you find it difficult to understand, simply post the data (captured announces data) here and someone will confirm it for you.
Tutorial to capture announces using Wireshark can be found at the below thread.~cloud99Code:https://www.sb-innovation.de/f59/how-capture-announces-wireshark-limited-http-trackers-only-33436/
You can dowload the updated qbittorrent 4.0.4 here:- Attachment 18641
Information regarding this particular client file has been based on the information from the announces you have provided at the below post.
Archived announces can be found here: Attachment 18642Code:http://www.sb-innovation.de/f46/ratiomaster-plus-2-1-a-33029/index23.html#post346991
1) Client is for qBittorrent 4.0.4 (macOS Version)
2) PeerID is set to non-global.
3) Key is set to non-global.
4) IPv6 and IPv4 address report disabled.
5) Supports encryption. (sends "&supportcrypto=1" paramater with announces)
~cloud99
Update for problem above:
tried with other versions of java jre 9, same result, also tried to point manualy trough Environment Variables, didnt work.
Only possible thing could be if im adding that line wrong in vmoptions
Attachment 18643
p.s. am i using correct section?
Yes and yes (otherwise it wouldnt let me save it).
Yes its from the link, also tried all other 9.x versions i could find, same with everything.
Tried troubleshooting instructions, cleaned all registry and appdata folders from bigly and java, and all over again... doesent work...
Attachment 18644
Where is Java installed? Where is BiglyBT installed?
If Java JRE is installed correctly, the following folder should exist and contain 3 files:
C:\ProgramData\Oracle\Java\javapath
Ensure java.exe, javaw.exe and javaws.exe exist in that folder, then view the properties to ensure it is 9.0.4 JRE.
The folder above should also be in your System PATH environment variable.